Technical Data Sheet
ELNYW200 XX
Revision Date: 1/6/2022
PRODUCT CODES:
ELNYW 200 XX (XX represents the sheen level)
AVAILABLE SHEENS:
10 – Flat, 20 – Low Gloss, 30 – Satin, 50 – Semi-gloss, 90 – Full Sheen
NAME:
ENVIROTHANE 200 WHITE TOPCOAT
DESCRIPTION:
Envirolak ELNYW 200XX is an opaque white finish that looks and feels like conventional varnish but offers greater flexibility without harmful solvents or catalysts. Based on a polyurethane dispersion, the coating is high build and suitable for tough environments like kitchens and baths. This product also has excellent levelling and anti- sag properties for vertical applications.
USES:
This product is designed for interior wood finishing applications such as cabinetry, tables, furniture and millwork.
PRODUCT PREPARATION:
Reduction is not required if spraying through a pump, but the product may be reduced with water or ELRX010 Reducer to improve application characeteristics depending on the equipment used. Product should be at room temperature and mixed thoroughly prior to finishing to ensure consistency and gloss.
Note: When used as a 2K product with ELCAT100 the gloss of ELNYW200XX will increase with increasing amounts of the hardener. Using 5% ELCAT100 will increase gloss 4-6 units and using 10% ELCAT100 will increase gloss 8-12 units.
RECOMMENDED APPLICATION:
Spray type:
Fluid Pressure:
Air Pressure:
Tips:
Air Assisted Airless
500-700 PSI
25 PSI (triggered)
06 or 09
Spray type:
Fluid Pressure:
Tips:
Airless
1200-2000 PSI
310 or 308, fine finish or ultra finish
Spray type:
Fluid Pressure:
Needle:
Reduction:
HLV (Turbine)
Max
1.5 – 1.8
2-5% ELRX010
Spray type:
Fluid Pressure:
Tips:
Reduction:
Cup Gun (gravity)
40 PSI
1.8
2-5% ELRX010
Wet Film Build:
Grams per 1/10 sq. metre: (250x400mm board) Number of Coats:
Maximum Dry Film Build:
Coating Temperature at Application:
4-6 mils
12-16g
1-2 depending on desired look
5 mils
20*C (68*F) or higher
*for colder temperatures, add reducer (ELRX010) or warm material prior to spraying
PHYSICAL PROPERTIES:
Specific Gravity:
Viscosity:
Solids Content:
Pot Life:
Flash Point:
VOC’s:
VOC’s (Less Exempt):
1.20 ± 2%
2000cps @20°C
40% by weight
None
>75°C
88 g/L, 0.73 lb/gal
182 g/L, 1.52 lb/gal
SANDING:
Sand between coats with 320 grit or Superfine Sponges. It is recommended to use this product in combination with ELPR170 Envirothane 170 White Primer as a basecoat.
DRYING TIMES:
Air dry:
(20°C/68°F)
Dry to Touch
Dry to Sand
Dry to Recoat
Dry to Stack
20 Minutes
2 Hours
4 hours at 4 wet mils (1K)
6 hours at 6 wet mils (1K)
2-3 hours at 4-6 wet mils (2K)
Overnight
Note: Good gentle air movement (not a hurricane) with a fan while parts are drying will reduce dry to sand times by 20-40% with reasonable humidity levels (<65% r.h.). Lower temperatures or higher humidity can greatly extend dry times.
Conventional Oven:
(40-45°C/104-113°F)
Dry to Touch
Dry to Sand
Dry to Recoat
Dry to Stack
10 Minutes
30-60 Minutes
1-2 hours
4-6 Hours
Sun-Spot IR Cure:
(Recommended)
Flash off
Direct Cure
Rack Cure (Indirect no probe mode)
Cool Down
Product is dry to sand (or stack) after cooling
1-2 Minutes
15-20 Minutes @60-70°C (140- 160°F)
30-40 Minutes @20%+ power
10-20 minutes
TYPICAL SYSTEMS:
Whites or Light Colours:
Substrate: MDF
ELPR170 Envirothane 170 White Primer
Sand using 320 grit sandpaper or fine sponge
ELPR170 Envirothane 170 White Primer
Sand using 320 grit sandpaper or fine sponge
1 or 2 coats ELNYW200XX Envirothane 200 White Topcoat
CLEANING:
Flush all equipment with water until it runs clear. Built-up coating and deep cleaning can be performed using ELRX110 EnviroKlean WB Cleaner. For best results cleaning tips, aircaps and unpainted parts use ELRX110 for one hour or 10-20 minutes in an Ultrasonic bath (max. temp. 50°C/120°F). Do not leave painted parts (i.e. spray guns) in ELRX110 for more than 20 minutes.
GENERAL INFORMATION:
Use stainless steel (304/316) equipment for all water based products. When switching between solvent and water based products in the same spray equipment we suggest the following:
From Solvent to Water: Wash with acetone, then wash with water.
From Water to Solvent: Wash with water, then wash with acetone.
Keep containers closed when not in use and keep from freezing.
These products are designed for industrial use only. Please refer to the Safety Data Sheet prior to use.
SHELF LIFE:
12 months in unopened containers
STORAGE:
Store in a tightly closed container at room temperature (18-25°C/64-75°F) and protect from direct sunlight and foreign material. Do not store at temperatures below 5°C/41°F.
Disclaimer: Every reasonable precaution is taken in the manufacture of our products to ensure that they comply with our standards. The information given herein is correct to the best of our knowledge. Any suggestions made by us covering the use of our products are based on experience and/or tests believed to be reliable. However, because the use of any product of our manufacture is completely beyond our control, including for example, the method and conditions of application, no guarantee or warranty, expressed or implied, is made. Manufacturer’s maximum liability shall be to replace such quantity of product determined by our laboratory to be defective. User shall determine the suitability of the product for his intended use and assumes all risk and liability in connection therewith.
