Technical Data Sheet
ELPR160
Revision Date: 8/29/23

PRODUCT CODES:

ELPR160

NAME:

ENVIROCRYL 160 WHITE PRIMER

DESCRIPTION:

ELPR160 is a Universal water based primer that provides an excellent foundation for any solid colour systems on solid wood, veneer, MDF or for refinishing as a 1K product. It offers fast dry times and is easy to sand. ELPR160 can also be applied over T9000 that has dried for 1-2 hours. It has excellent leveling and anti-sag for vertical applications and very easy to spray brush or roll. It can also be used as a 2K product by adding 5% CAT100LV Hardener. After priming, PR160 is suitable to be topcoated with Envirolak’s 200, 400 or 800 series and many other topcoats. Do not use 100 series over PR160.

USES:

This product is designed for interior wood finishing applications such as cabinetry, tables, furniture and millwork.

PRODUCT PREPARATION:

Reduction is not required when spraying with Air Assisted Airless, Airless, pressure pots, HVLP turbine and conventional cup guns but the product may be reduced with water or ELRX010 Reducer if desired or when brushing and rolling to improve leveling. Product should be at room temperature and mixed thoroughly prior to application.

SANDING:

Raw wood substrate should be sanded with 120-180 grit sandpaper prior to applying primer. Sand primer with 320 grit sandpaper and refine with super fine sponges if needed.

RECOMMENDED APPLICATION:

Spray type:
Fluid Pressure:
Air Pressure:
Tips:       Kremlin
                 Wagner
                 Graco/CA and others

Air Assisted Airless
400-600 PSI
25 PSI (triggered)
04114, 06114, 09114, 09154
0950, 1150, 1350, 1360, 1380
411, 413, 511, 513, 611, 613

Spray type:
Fluid Pressure:
Tips:     Fine Finish or Ultra Finish
Reduction:

Airless
2000-2200 PS
308, 408, 508
Not required, water or RX010 optional

Spray type:
Fluid Pressure:
Needle:

HLV (Turbine)
Max
1.5 – 1.8

Spray type:
Fluid Pressure:
Tips:
Reduction:

Cup Gun (gravity)
40 PSI
1.8
Not required, water or RX010 optional

Wet Film Build:
Grams per 1/10 sq. metre: (250x400mm board) Number of Coats:
Maximum Dry Film Build:

Coating Temperature at Application:

6-7 mils
21-25
1-2 depending on desired look
6 mils

16*C (60*F) or higher

PHYSICAL PROPERTIES:

Specific Gravity:
Viscosity:
Solids Content:
Pot Life:
Flash Point:
VOC’s (Less Exempt):

1.38 ± 2%
3500-4000cps @20°C
57% by weight
None
>75°C
169 g/L, 1.4 lb/gal

DRYING TIMES:

Air dry:

(20°C/68°F)

with air movement

Dry to Touch
Dry to Sand
Dry to Recoat
Dry to Stack

10-15 Minutes
1 Hour
1-2Hours
4 Hours

Note: Good gentle air movement (not a hurricane) with a fan while parts are drying will reduce dry to sand times by 20-40% with reasonable humidity levels (<65% r.h.). Lower temperatures or higher humidity can greatly extend dry times.

Conventional Oven:

(40-45°C/104-113°F)

Dry to Touch
Dry to Sand
Dry to Recoat
Dry to Stack

10 Minutes
30 Minutes
30-60 Minutes
1 Hour

Sun-Spot IR Cure:

(Recommended)

Flash off
Direct Cure
Rack Cure (Indirect no probe mode)
Cool Down
Product is dry to sand (or stack) after cooling

2 Minutes
5  Min. @60-70°C (140-160°F)
10 Minutes @20%+ power
10-20 minutes

TYPICAL SYSTEMS:

Solid Wood, Venners, MDF, T9000 or old sovent finishes

Sand raw wood 120-180
ELPR160-TB Envirocryl 160 Tannin Blocking White Primer 1k or 2k
Sand using 240 or 320 grit sandpaper
ELPR160-TB Envirocryl 160-TB Tannin Blocking White Primer 1k or 2k
Sand using 320 or 400 grit sandpaper, refine with super fine sponges if desired 1 or 2 coats ELNYW200XX or ELACW400XX or ELNYW800XX 1K or 2K

CLEANING:

Flush all equipment with water until it runs clear. Built-up coating and deep cleaning can be performed using ELRX110 EnviroKlean WB Cleaner. For best results cleaning tips, aircaps and unpainted parts use ELRX110 for one hour or 10-20 minutes in an Ultrasonic bath (max. temp. 50°C/120°F). Do not leave painted parts (i.e. spray guns) in ELRX110 for more than 20 minutes.

GENERAL INFORMATION:

Use stainless steel (304/316) equipment for all water based products. When switching between solvent and water based products in the same spray equipment we suggest the following:

From Solvent to Water: Wash with acetone, then wash with water.

From Water to Solvent: Wash with water, then wash with acetone.
Keep containers closed when not in use and keep from freezing.
These products are designed for industrial use only. Please refer to the Safety Data Sheet prior to use.

SHELF LIFE:

12 months in unopened containers

STORAGE:

Store in a tightly closed container at room temperature (18-25°C/64-75°F) and protect from direct sunlight and foreign material. Do not store at temperatures below 5°C/41°F.

Disclaimer: Every reasonable precaution is taken in the manufacture of our products to ensure that they comply with our standards. The information given herein is correct to the best of our knowledge. Any suggestions made by us covering the use of our products are based on experience and/or tests believed to be reliable. However, because the use of any product of our manufacture is completely beyond our control, including for example, the method and conditions of application, no guarantee or warranty, expressed or implied, is made. Manufacturer’s maximum liability shall be to replace such quantity of product determined by our laboratory to be defective. User shall determine the suitability of the product for his intended use and assumes all risk and liability in connection therewith. 

Scroll to Top