PRODUCT CODES:
EL125XX (EL12505, EL12530)
NAME:
ENVIROTHANE 125 LOW SLIP CLEAR SELF SEAL TOPCOAT
AVAILABLE SHEENS:
| EL125 05 | 5 Gloss - Deat Flat |
| EL125 30 | 30 Gloss - Satin |
DESCRIPTION:
EL125XX series is a warm clear urethane clear topcoat that provides a low-slip, durable finish for wood floors and stairs. This product offers outstanding durability and stain resistance with the wood warmth of traditional solvent-based coatings, all in a low VOC water based finish that can readily be applied in the shop or on-site. The product can also be catalyzed with CAT100-LV hardener or crosslinked with CAT150 crosslinker to improve chemical, scratch, mar resistance and vertical flow.
USES:
This product is specially designed for interior wood flooring and stairs. It can be sprayed, brushed or rolled on and is easy to touch up.
PRODUCT PREPARATION:
Reduction is not required, but you may reduce the product with 3% RX010 reducer or 5- 10% water if desired. Product should be at room temperature and mixed thoroughly prior to finishing to ensure consistency and gloss.
CATALYST RATIOS USING CAT100-LV HARDENER
| EL125 XX Series | by weight ~10% | by volume ~10% (10:1) |
|---|---|---|
| (approx. 2 hr pot life @10%) | 2.4kg (2 cans) per 19.6kg (5 GA) pail | 2.12L (2 cans) per 5 GA |
| (approx. 4 hr pot life @5%) | 480g (2/5 can) per 3.9kg (1 GA) | 425mL/14.4oz.(2/5 can) per GA |
CATALYST RATIOS USING CAT150 CROSSLINKER
| EL125 XX Series | by weight ~ by volume |
|---|---|
| Per Quart: | 29 grams, 25mL ~ 0.9 fl oz. |
| Per Gallon: | 117 grams, 100mL ~ 3.4 fl oz. |
| Per Pail (5 GA): | 582 grams, 497mL ~ 17 fl oz. |
RECOMMENDED APPLICATION:
| Spray type: Air Assisted Airless | |
|---|---|
| Fluid Pressure: | 500-600 PSI |
| Air Pressure: | 25 PSI (triggered) |
| Tips: Kremlin | 04114, 06114, 09114, 09154 |
| Wagner | 0950, 1150, 1350, 1360, 1380 |
| Graco/CA and others | 411, 413, 511, 513, 611, 613 |
| Reduction:Hand Spray | 0-3% RX010 or 0-10% H20 |
| Reduction:Machine Spray (Recip or Rotary) | 0-3% RX010 or 0-10% H20 |
| Spray type: Airless | |
|---|---|
| Fluid Pressure: | 2000-3000 PSI |
| Tips: Fine Finish, Ultra Finish or Skill Tip | 306, 308, 408, 508, 06-17 |
| Reduction:Hand Spray | 0-3% RX010 or 0-10% H20 |
| Reduction:Machine Spray (Recip or Rotary) | 0-3% RX010 or 0-10% H20 |
| Spray type: HVLP (Turbine) 5 stage or higher | |
|---|---|
| Air Pressure: | Max |
| Needle: | 1.8-2.0 needle high solids air cap |
| Reduction: | 3-5% ELRX010 or 10-15% water |
| Spray type: Cup Gun (gravity) | |
|---|---|
| Air Pressure: | 25-35 PSI |
| Tips: | 1.8 needle |
| Reduction: | 2-5% ELRX010 or 10-15% Water |
| Brush: | Medium/Firm Nylon or Polyester |
| Roll: | Mohair, Velour or 3/16 Microfiber |
| Reduction: | 0-3% ELRX010 or 0-10% Water |
PHYSICAL PROPERTIES:
Specific Gravity:1.02 ± 2%
Viscosity: 600-800 cps. at 20°C
Solids Content: 21% by weight
Pot Life: None
Flash Point: >75°C
VOC’s: 36 g/L, 0.29 lbs/GA
VOC’s (less exempt): 146 g/L, 1.22 lbs/GA
DRYING TIMES:
Air dry:
(20°C/68°F)
Dry to Touch: 10 Minutes
Dry to Sand: 1 Hour
Dry to Stack: 8-12 Hours
Note: Gentle air movement (recirculator or fan) while parts are drying will reduce dry to sand times by 20-40%
Conventional Oven:
(40-45°C/104-113°F)
Dry to Touch: 5 Minutes
Dry to Sand: 20-30 Minutes
Dry to Stack: 3-4 Hours
Sun-Spot IR Cure:
Flash off: Not required
Full Cure: 10 Minutes @60-70°C(140-160°F)
Cool: 5-10 minutes
Product is dry to sand (or stack) after cooling
TYPICAL SYSTEMS:
Substrate: Various Woods, oily or exotic woods will require a special sealer Water based Wiping or Spray Stain, ELSWB104 or ELSSB100
EL125 XX Envirothane 100 Warm Clear Self Seal Topcoat
Sand using 320 grit sandpaper or Superfine sponges EL125 XX Envirothane 100 Warm Clear Self Seal Topcoat
GENERAL INFORMATION:
Use stainless steel (304/316) equipment for all water based products. When switching between solvent and water based products in the same spray equipment we suggest the following:
- From Solvent to Water: Wash with acetone, then wash with water.
- From Water to Solvent: Wash with water, then wash with acetone.
Keep containers closed when not in use and keep from freezing.
These products are designed for industrial use only. Please refer to the Safety Data Sheet prior to use.
SHELF LIFE:
12 months in unopened containers
STORAGE
Store in a tightly closed container at room temperature (18-25°C/64-75°F) and protect from direct sunlight and foreign material. Do not store at temperatures below 5°C/41°F.
Disclaimer: Every reasonable precaution is taken in the manufacture of our products to ensure that they comply with our standards. The information given herein is correct to the best of our knowledge. Any suggestions made by us covering the use of our products are based on experience and/or tests believed to be reliable. However, because the use of any product of our manufacture is completely beyond our control, including for example, the method and conditions of application, no guarantee or warranty, expressed or implied, is made. Manufacturer’s maximum liability shall be to replace such quantity of product determined by our laboratory to be defective. User shall determine the suitability of the product for his intended use and assumes all risk and liability in connection therewith.
