NAME:
ENVIROCRYL 400 WHITE TOPCOAT
AVAILABLE SHEENS:
ELACW400 10 10 Gloss – Flat
ELACW400 20 20 Gloss – Low Gloss
ELACW400 30 30 Gloss – Satin
DESCRIPTION:
ELACW400XX series is a white acrylic topcoat that is easy to spray at low pressures, is fast drying and offers good feel and early block resistance in an economical package. This product can be tinted to any off white or pastel colour, has high build and is suitable for tough environments like kitchens and baths when used as a 1K product and can also be crosslinked with CAT150 crosslinker to improve vertical flow, chemical and mar resistance. This product also has excellent levelling and anti- sag properties for vertical applications and helps prevent bridging. 400 series can be applied over T9000 primer when used as a 1K in 1-2 hours in simple air dry conditions.
USES:
This product is designed for interior wood finishing applications such as cabinetry, furniture and millwork.
PRODUCT PREPARATION:
Reduction is not required when spraying with Air Assisted Airless, Airless, pressure pots, HVLP turbine and conventional cup guns but the product may be reduced with water or ELRX010 Reducer if desired or when brusing and rolling to improve leveling. Product should be at room temperature and mixed thoroughly prior to application.
CATALYST RATIOS USING
CAT150 CROSSLINKER
ELNYW400 XX
by weight ~ by volume
Per Quart: 34 grams, 29mL ~ 1 fl oz.
Per Gallon: 135 grams, 116mL ~ 4 fl oz.
Per Pail (5 GA): 680 grams, 582mL ~ 20 fl oz.
RECOMMENDED APPLICATION:
Spray type: Air Assisted Airless
Fluid Pressure: 400-600 PSI
Air Pressure: 25 PSI (triggered)
Tips:
Kremlin 04114, 06114, 09154
Wagner 0950, 1150, 1350, 1360
Graco/CA and others 409, 411, 413, 511, 513, 611
Reduction:Hand Spray Not required
Reduction:Machine Spray (Recip or Rotary) Not required
Spray type: Airless
Fluid Pressure: 2000-3000 PSI
Tips: Fine Finish, Ultra Finish or Skill Tip 306, 308, 408, 508, 04-17, 06-17
Reduction: Hand Spray Not required
Reduction: Machine Spray (Recip or Rotary) Not required
Spray type: HVLP (Turbine) 5 stage or higher
Air Pressure: Max
Needle: 1.8 needle high solids air cap
Reduction: 0-5% ELRX010 or 0-10% water
Spray type: Cup Gun (gravity)
Air Pressure: 25-35 PSI
Tips: 1.8 needle
Reduction: 0-5% ELRX010 or 0-10% water
Brush: Medium/Firm Nylon or Polyester
Roll: Mohair, Velour or 3/16 Microfiber
Reduction: 0-3% ELRX010 or 0-10% water
Wet Film Build: 4-6 mils
Grams per 1/10 sq. metre: (250x400mm board) 13-19 grams (3.2g/wet mil)
Number of Coats: 1 – 2
Maximum Dry Film Build: 6 mils
Coating Temperature at Application: 18°C (65°F) or higher
PHYSICAL PROPERTIES:
Specific Gravity: 1.25 ± 2%
Viscosity: 3500 cps @20°C
Solids Content: 48% by weight (35% by vol.)
Flash Point: >75°C
VOC’s: 40 g/L
VOC’s (minus exempt): 117 g/L, 0.99 lb/gal
SANDING
DRYING TIMES:
Air dry:
(20°C/68°F)
Dry to Touch: 20 Minutes
Dry to Sand: 1 hour
Dry to Recoat: 1-2 hours
Dry to Stack: 2 hours
Conventional Oven:
(40-45°C/104-113°F)
Dry to Sand: 30 Minutes
Dry to Recoat: 30-60 Minutes
Dry to Stack: 1 hour
Sun-Spot IR Cure:
(Recommended)
Flash off: 2 Minutes
Direct Cure: 4-5 Minutes @60-70°C (140-160F)
Rack Cure: 10 minutes @10%+ power
Cool Down: 10-20 Minutes
Product is dry to stack (or sand) after cooling
TYPICAL SYSTEMS:
Whites or Light Colours
Refinishing - Over Old Finishes
Prep: Degrease, premix 1 part RX110 (Enviroklean) – 4 parts water, spray on surface, scrub with maroon scotchbrite or stiff nylon brush to loosen grease and contamination, wipe clean with wet rag with water to remove Enviroklean, wipe again with a dry rag to remove any remaining EnviroKlean or grease, allow to dry and sand with 180 grit or fine sponges
ELPRT9000 1K or ELPR160-TB 1K or ELPR170/170TB 2K with CAT100LV
Sand using 320 grit sandpaper or fine sponges
ELPRT9000 1K or ELPR160TB 1K or ELPR170/170TB 2K with CAT100LV
Level Sand using 320 grit sandpaper and V fine or S Fine sponges
1 or 2 coats ELACW400XX Topcoat 1K or crosslinked with CAT150
TYPICAL SYSTEMS:
Whites or Light Colours
Substrate: MDF
ELPR160-TB 1K or ELPR170 or ELPR170TB 1K or 2K with CAT100LV
Sand using 320 grit sandpaper or fine sponges
ELPR160-TB 1K or ELPR170 or ELPR170TB 1K or 2K with CAT100LV
1 or 2 coats ELACW400XX Topcoat 1K or crosslinked with CAT150
TYPICAL SYSTEMS:
Whites or Light Colours
Substrate: Natural woods and veneers
ELPRT9000 1K or ELPRT160-TB 1K or ELPR170 2K or ELPR170-TB 2K
Sand using 320 grit sandpaper or fine sponges
ELPRT9000 1K or ELPRT160-TB 1K or ELPR170 2K or ELPR170-TB 2K
Level Sand using 320 grit sandpaper and V fine or S Fine sponges
1 or 2 coats ELACW400XX Topcoat 1K or crosslinked with CAT150
GENERAL INFORMATION:
Use stainless steel or plastic equipment for all water based products. When switching between solvent and water based products in the same spray equipment we suggest the following:
- From Solvent to Water: Wash with acetone, then wash with water.
- From Water to Solvent: Wash with water, then wash with acetone.
Keep containers closed when not in use and wash all equipment well. Keep from freezing.
These products are designed for industrial use only. Please refer to the Safety Data Sheet prior to use.
SHELF LIFE:
12 months in unopened containers
STORAGE
Disclaimer: Every reasonable precaution is taken in the manufacture of our products to ensure that they comply with our standards. The information given herein is correct to the best of our knowledge. Any suggestions made by us covering the use of our products are based on experience and/or tests believed to be reliable. However, because the use of any product of our manufacture is completely beyond our control, including for example, the method and conditions of application, no guarantee or warranty, expressed or implied, is made. Manufacturer’s maximum liability shall be to replace such quantity of product determined by our laboratory to be defective. User shall determine the suitability of the product for his intended use and assumes all risk and liability in connection therewith.
