NAME:
Envirocryl 510 Deep Tint Base Topcoat
AVAILABLE SHEENS:
ELAN51010 10 Gloss – Flat
ELAN51020 20 20 Gloss – Low Gloss
ELAN51030 30 Gloss – Satin
DESCRIPTION:
ELAN510XX series is an acrylic urethane deep tint base topcoat that is easy to spray at low pressures, is fast drying and offers a waxy feel and early block resistance in an economical package. This product can be tinted to any dark colour, has high build for great hiding with one coat coverage of 320 grit sanding scratches or previously painted surfaces. It is suitable for tough environments like kitchens and baths when used as a 1K product and can also be catalyzed with CAT100LV hardener (4-6hr pot life) to improve adhesion, vertical flow, chemical and mar resistance or crosslinked with CAT150 crosslinker to improve vertical flow, chemical and marr resistance. This product also has excellent levelling and anti-sag properties for vertical applications. 510 series can be applied over T9000 primer when used as a 1K in 1-2 hours in simple air dry conditions.
USES:
This product is designed as a dark tint base topcoat for interior wood finishing applications such as cabinetry, furniture and millwork.
PRODUCT PREPARATION:
This product is designed to be sprayed out of the can without the need for reduction but may be reduced with water or RX010 reducer if desired. Store at room temperature and mixed thoroughly prior to finishing to ensure consistency and gloss.
2K MXING RATIOS:
| CAT100-LV Hardener (5%) | CAT150 Crosslinker (3%) |
|---|---|
| Per Quart: 60g/50mL/1.8floz. | 29 grams, 25mL ~ 0.9 fl oz. |
| Per Gallon: 240g/200mL | 117 grams, 100mL ~ 3.4 fl oz. |
| Per Pail (5 GA): 1.2kg (1 jar) | 582 grams, 497mL ~ 17 fl oz. |
RECOMMENDED APPLICATION:
Spray type: Air Assisted Airless
Fluid Pressure: 400-600 PSI
Air Pressure: 30-35 PSI (triggered)
Tips:
Kremlin 04114, 06114, 09114, 09154
Wagner 0950, 1150, 1350, 1360, 1380
Graco/CA and others 411, 413, 511, 513, 611, 613
Reduction: Not required, water or RX010 optional
Spray type: Airless
Fluid Pressure: 1500-2000 PSI
Tips: Fine Finish or Ultra Finish 306, 308, 408, 508
Reduction: Not required, water or RX010 optional
Spray type: HVLP (Turbine)5 stage or higher
Air Pressure: Max
Tips: 1.8 Needle high solids air cap
Reduction: Not required, water or ELRX010 optional
Spray type: Cup Gun (gravity)
Air Pressure: 30-35 PSI
Tips: 1.8 Needle
Reduction: Not required, water or ELRX010 optional
Brush: Medium/Firm Nylon or Polyester
Roll: Mohair, Velour or 3/16 Microfiber
Reduction: 0-3% ELRX010 or 0-10% water
PHYSICAL PROPERTIES:
Specific Gravity: 1.03 ± 2%
Viscosity: 4000 – 4500 cps @22°C
Solids Content: 31% by weight
Flash Point: >93°C
VOC’s: 69 g/L, 0.57 lb/gal
VOC’s (minus exempt): 190 g/L, 1.57 lb/gal
DRYING TIMES:
Air dry:
(20°C/68°F)
Dry to Touch: 20 – 25 Minutes
Dry to Sand: 1 hour
Dry to Recoat: 1-2 hours
Dry to Stack: 2 hours
Note: Gentle air movement (recirculator or fan) while parts are drying will reduce dry to sand times by 20-40%
Conventional Oven:
(40-45°C/104-113°F)
Dry to Sand: 30 Minutes
Dry to Recoat: 30-60 Minutes
Dry to Stack: 1 hour
Sun-Spot IR Cure:
(Recommended)
Flash off: 2 Minutes
Direct Cure: 4-5 Minutes @60-70°C (140-160F)
Rack Cure: 10 minutes @10%+ power
Cool Down: 10-20 Minutes
Product is dry to stack (or sand) after cooling
TYPICAL SYSTEMS:
Dark Colours:
Refinishing - over old finishes
Prep: Degrease, premix 1 part RX110 (Enviroklean) – 4 parts water, spray on surface, scrub with maroon scotchbrite or stiff nylon brush to loosen grease and contamination, wipe clean with wet rag with water to remove Enviroklean, wipe again with a dry rag to remove any remaining EnviroKlean or grease, allow to dry and sand with 180 grit or fine sponges
ELPRT9000 1K or ELPR160TB 1K or ELPR180/ELPR170/170TB 2K with CAT100LV Sand using 320 grit sandpaper or fine sponges
ELPRT9000 1K or ELPR160TB 1K or ELPR180/ELPR170/170TB 2K with CAT100LV Level Sand using 320 grit sandpaper and V fine or S Fine sponges
ELAN510XX Tinted Topcoat 1K or 2K with CAT150 or CAT100LV
TYPICAL SYSTEMS:
Dark Colours
Substrate: MDF
ELPRT9000 or ELPR160TB 1K or ELPR180/PR170/170TB 1K or 2K with CAT100LV Sand using 320 grit sandpaper or fine sponges
ELPRT9000 or ELPR160TB 1K or ELPR180/PR170/170TB 1K or 2K with CAT100LV Level Sand using 320 grit sandpaper and V fine or S Fine sponges
ELAN510XX Tinted Topcoat 1K or 2K with CAT150 or CAT100LV
TYPICAL SYSTEMS:
Dark Colours
Substrate: Natural woods and veneers
ELPRT9000 or ELPR160TB 1K or ELPR180/PR170/170TB 2K with CAT100LV Sand using 320 grit sandpaper or fine sponges
ELPRT9000 or ELPR160TB 1K or ELPR180/PR170/170TB 2K with CAT100LV Level Sand using 320 grit sandpaper and V fine or S Fine sponges ELAN510XX Tinted Topcoat 1K or 2K with CAT150 or CAT100LV
GENERAL INFORMATION:
Use stainless steel or plastic equipment for all water based products. When switching between solvent and water based products in the same spray equipment we suggest the following:
- From Solvent to Water: Wash with acetone, then wash with water.
- From Water to Solvent: Wash with water, then wash with acetone.
Keep containers closed when not in use and wash all equipment well. Keep from freezing.
These products are designed for industrial use only. Please refer to the Safety Data Sheet prior to use.
SHELF LIFE:
12 months in unopened containers
STORAGE
Store in a tightly closed container at room temperature (18-25°C/64-75°F) and protect from direct sunlight and foreign material. Do not store at temperatures below 5°C/41°F.
Disclaimer: Every reasonable precaution is taken in the manufacture of our products to ensure that they comply with our standards. The information given herein is correct to the best of our knowledge. Any suggestions made by us covering the use of our products are based on experience and/or tests believed to be reliable. However, because the use of any product of our manufacture is completely beyond our control, including for example, the method and conditions of application, no guarantee or warranty, expressed or implied, is made. Manufacturer’s maximum liability shall be to replace such quantity of product determined by our laboratory to be defective. User shall determine the suitability of the product for his intended use and assumes all risk and liability in connection therewith.
