PRODUCT CODES:
ELNYC300XX (ELNYC30003, ELNYC30005, ELNYC30010, ELNYC30020) (ELNYC30030, ELNYC30050, ELNYC30090)
NAME:
ENVIROTHANE 300 CRYSTAL CLEAR TOPCOAT
AVAILABLE SHEENS:
| ELNYC300 03 | 3 Gloss - Ultra-matte (Natural look) |
| ELNYC300 05 | 5 Gloss - Dead Flat |
| ELNYC300 10 | 10 Gloss - Flat |
| ELNYC300 20 | 20 Gloss - Low Gloss |
| ELNYC300 30 | 30 Gloss - Satin |
| ELNYC300 50 | 50 Gloss - Semi Gloss |
| ELNYC300 90 | 90 Gloss - High Gloss |
DESCRIPTION:
ELNYC300XX series is a water-white clear urethane topcoat that is easy to apply, ultra clear and intended for use over white basecoats in a glazed system or in clear systems where maximum clarity is desired over light or dark stains. The finished product offers an incredibly smooth and durable finish that is resistant to staining and marking. ELNYC300XX meets or exceeds KCMA standards when used 1K and can also be catalyzed with CAT100-LV hardener to improve adhesion, vertical flow, chemical and mar resistance or crosslinked with CAT150 crosslinker to improve vertical flow, chemical and mar resistance.
USES:
This product is designed for interior wood finishing applications such as tables, bar tops, cabinetry, furniture, flooring, and millwork.
PRODUCT PREPARATION:
Reduction is not required if spraying through a pump, but the product may be reduced with water or ELRX010 Reducer to improve application characeteristics depending on the equipment used. Product should be at room temperature and mixed thoroughly prior to finishing to ensure consistency and gloss.
CATALYST RATIOS USING CAT100-LV HARDENER
| ELNYC300 XX Series | by weight ~10% | by volume ~10% (10:1) |
|---|---|---|
| (approx. 2 hr pot life @10%) | 2.4kg (2 cans) per 19.6kg (5 GA) pail | 2.12L (2 cans) per 5 GA |
| (approx. 4 hr pot life @5%) | 480g (2/5 can) per 3.9kg (1 GA) | 425mL/14.4oz.(2/5 can) per GA |
CATALYST RATIOS USING CAT150 CROSSLINKER
| ELNYC300 XX Series | by weight ~ by volume |
|---|---|
| Per Quart: | 29 grams, 25mL ~ 0.9 fl oz. |
| Per Gallon: | 117 grams, 100mL ~ 3.4 fl oz. |
| Per Pail (5 GA): | 582 grams, 497mL ~ 17 fl oz. |
RECOMMENDED APPLICATION:
| Spray type: Air Assisted Airless | |
|---|---|
| Fluid Pressure: | 500-600 PSI |
| Air Pressure: | 25 PSI (triggered) |
| Tips: Kremlin | 04114, 06114, 09114, 09154 |
| Wagner | 0950, 1150, 1350, 1360, 1380 |
| Graco/CA and others | 411, 413, 511, 513, 611, 613 |
| Reduction:Hand Spray | 0-3% RX010 or 0-10% H20 |
| Reduction:Machine Spray (Recip or Rotary) | 0-3% RX010 or 0-10% H20 |
| Spray type: Airless | |
|---|---|
| Fluid Pressure: | 2000-3000 PSI |
| Tips: Fine Finish, Ultra Finish or Skill Tip | 306, 308, 408, 508, 06-17 |
| Reduction:Hand Spray | 0-3% RX010 or 0-10% H20 |
| Reduction:Machine Spray (Recip or Rotary) | 0-3% RX010 or 0-10% H20 |
| Spray type: HVLP (Turbine) 5 stage or higher | |
|---|---|
| Air Pressure: | Max |
| Needle: | 1.8-2.0 needle high solids air cap |
| Reduction: | 3-5% ELRX010 or 10-15% water |
| Spray type: Cup Gun (gravity) | |
|---|---|
| Air Pressure: | 25-35 PSI |
| Tips: | 1.8 needle |
| Reduction: | 2-5% ELRX010 or 10-15% Water |
| Brush: | Medium/Firm Nylon or Polyester |
| Roll: | Mohair, Velour or 3/16 Microfiber |
| Reduction: | 3-5% ELRX010 or 10-20% Water |
| Wet Film Build: | 4-6 mils |
|---|---|
| Grams per 1/10 sq. metre: (250x400mm board) | 8.5-11g |
| Number of Coats: | 2-3 depending on desired look |
| Maximum Dry Film Build: | 5 mils |
| Coating Temperature at Application: | 20°C (68°F) or higher |
*for colder temperatures, add reducer (ELRX010) or warm material prior to spraying
PHYSICAL PROPERTIES:
Specific Gravity:1.04 ± 2%
Viscosity: 1200 cps. at 20°C
Solids Content: 30% by weight
Pot Life: NA
Flash Point: >75°C
VOC’s: 117 g/L, 0.98 lb/gal
VOC’s (less exempt): 270 g/L, 2.25 lb/gal
SANDING:
Sand raw wood 150- 180 grit to remove any mill glaze, wide belt scratches or oxidation. Sand SEAL500 sealer or 300XX as a self seal between coats with 320 or 400 grit sandpaper and refine with superfine sponges.
DRYING TIMES:
Air dry:
(20°C/68°F)
Dry to Touch: 20 Minutes
Dry to Sand: 1-2 Hours
Dry to Stack: 12-16 Hours
Note: Good gentle air movement (not a hurricane) with a recirculator or fan while parts are drying will reduce dry to sand times by 20-40% with reasonable humidity levels (<65% r.h.). Lower temperatures or higher humidity will extend dry times.
Conventional Oven:
(40-45°C/104-113°F)
Dry to Touch: 10 Minutes
Dry to Sand: 30-60 Minutes
Dry to Stack: 3-4 Hours
Sun-Spot IR Cure:
Flash off: 10-15 Minutes
Direct Cure: 5-10 Minutes @60-70°C(140-160°F)
Rack Cure (Indirect no probe mode): 10-30 Minutes @20%+ power
Cool: 10-20 minutes
Product is dry to sand (or stack) after cooling
TYPICAL SYSTEMS:
Glazed System:
Substrate: MDF
ELPR170 or ELPR170-TB or ELPR160-TB Primer 1K or 2K
Sand using 320 grit sandpaper or fine sponges
ELPR170 or ELPR170-TB or ELPR160-TB Primer 1K or 2K
Sand using 320-400 grit sandpaper and refine with superfine sponges
ELNYW200XX Topcoat 1K or 2K with CAT100LV or 2K with CAT150
ELDGB100 Tinted Dry Glaze
Sand off glaze with maroon Scotch Brite or super fine sponges to highlight profiles or create brush lines
ELNYC300XX Crystal Clear Topcoat 1K or 2K with CAT100LV or 2K with CAT150
Stain System:
Substrate: Various Woods, check adhesion on oily woods (teak, ipe, brazilian cherry, etc.) Sand raw wood with 150 or 180 grit sandpaper and fine sponges prior to finishing Envirostain wiping, spray, roll coat or dipping stain SEAL500 1K or 2K with CAT100LV Sand between coats using 320-400 grit sandpaper and refine with superfine sponges ELNYC300XX 2K with CAT100LV
Stain System:
Substrate: Various Woods, check adhesion on oily woods (teak, ipe, brazilian cherry, etc.) prior to finishing
Sand raw wood with 150 or 180 grit sandpaper and fine sponges
Envirostain wiping, spray, roll coat or dipping stain
ELNYC300XX 1K or 2K with CAT100LV or 2K with CAT150 Crosslinker Sand using 320-400 grit sandpaper and refine with superfine sponges ELNYC300XX 1K or 2K with CAT100LV or 2K with CAT150 Crosslinker
CLEANING:
Flush all equipment with water until it runs clear. Built-up coating and deep cleaning can be performed using ELRX110 EnviroKlean WB Cleaner. For best results cleaning tips, aircaps and unpainted parts use ELRX110 for one hour or 10-20 minutes in an Ultrasonic bath (max. temp. 50°C/120°F). Do not leave painted parts (i.e. spray guns) in ELRX110 for more than 20 minutes.
GENERAL INFORMATION:
Use stainless steel (304/316) equipment for all water based products. When switching between solvent and water based products in the same spray equipment we suggest the following:
- From Solvent to Water: Wash with acetone, then wash with water.
- From Water to Solvent: Wash with water, then wash with acetone.
Keep containers closed when not in use and keep from freezing.
These products are designed for industrial use only. Please refer to the Safety Data Sheet prior to use.
SHELF LIFE:
12 months in unopened containers
STORAGE
Store in a tightly closed container at room temperature (18-25°C/64-75°F) and protect from direct sunlight and foreign material. Do not store at temperatures below 5°C/41°F.
Disclaimer: Every reasonable precaution is taken in the manufacture of our products to ensure that they comply with our standards. The information given herein is correct to the best of our knowledge. Any suggestions made by us covering the use of our products are based on experience and/or tests believed to be reliable. However, because the use of any product of our manufacture is completely beyond our control, including for example, the method and conditions of application, no guarantee or warranty, expressed or implied, is made. Manufacturer’s maximum liability shall be to replace such quantity of product determined by our laboratory to be defective. User shall determine the suitability of the product for his intended use and assumes all risk and liability in connection therewith.
