PRODUCT CODES:
ELNYC900 00
NAME:
ENVIROTHANE 900 RAW CLEAR NATURAL EFFECT 0 SHEEN
AVAILABLE SHEENS:
ELNYC900 00 | Ultra-matte (0-2 sheen) |
DESCRIPTION:
ELNYC900 00 Raw is a clear urethane topcoat that can be used to achieve the look of raw, unfinished wood, while adding the protection of a high quality wood finish. The product is easy to spray through all types of spray equipment and is capable of achieving gloss values less than 1 when applied to wood substrates. Despite being an “ultra-low” sheen product the 900 00 Raw offers outstanding mar resistance and doesn’t “wet” (darken) the wood substrate, leaving a very natural looking finish. For best performance on cabinetry or furniture it is recommended to add 2-3% CAT150 Crosslinker (no wood wetting) Adding CAT100-LV Hardener at 3-10% will add some wood wetting and increase clarity for use over stains when muting the wood is not desired, 10% addition will increase the gloss to 2 sheen). ELNYC900 00 can also be tinted to any dark colour for the ultimate 0.5-2 sheen solid dark colour system with self healing anti scratch and non marring properties. For decorative applications such as ceiling panels ELNYC900 00 can be used as a one component finish.
USES:
This product is designed as a clearcoat or dark solid colour for interior wood finishing applications such as cabinetry, furniture and millwork.
PRODUCT PREPARATION:
Reduction is not required. Product should be at room temperature and mixed thoroughly prior to each use to ensure consistency and gloss.
2K MIXING RATIOS:
CAT150 Crosslinker (2%) | CAT100-LV Hardener (10%) | |
---|---|---|
QT | 20 grams/18mL/0.6 oz. | 120 grams/100mL/3.6 oz |
GA | 80 grams/65mL/2.3 oz | 480 grams/400mL/12.8 oz |
5GA | 385 grams/330mL/11 oz | 1200 grams/945ml/36 oz |
No Pot Life | 4 Hour Pot Life |
SANDING:
Substrate should be sanded with 180 grit sandpaper prior to finishing. Use as a Self Seal system sanding the first coat with 320 grit or Superfine Sponges.
RECOMMENDED APPLICATION:
Spray type: Air Assisted Airless | |
---|---|
Fluid Pressure | 300-600 PSI |
Air Pressure | 30 PSI (triggered) |
Tips | Kremlin 03114, 04114, 06114, 06154 Wagner 0950, 1150, 1350, 1360 Graco/CA and others 411, 413, 511, 513, 611 |
Spray type: Airless | |
---|---|
Fluid Pressure | 1500-2000 PSI |
Tips | Fine Finish or Ultra Finish 306, 308, 408, 508 |
Reduction | Not Required |
Spray type: Cup Gun (gravity) | |
---|---|
Air Pressure | 25-30 PSI |
Tips | 1.5 — 1.8 |
Reduction | Not required |
Spray type: HVLP (Turbine) 5 stage or higher | |
---|---|
Air Pressure | Max |
Needle | 1.8 needle high solids air cap |
Reduction | Not required |
Hand Application | |
---|---|
Brush | Medium/Firm Nylon or Polyester |
Roll | Mohair, Velour or 3/16 Microfiber |
Reduction | 0-3% ELRX010 or 0-10% water |
Wet Film Build | 3-4 mils |
---|---|
Grams per 1/10 sq. metre | (250x400mm board) 8-11 grams (2.6 grams/mil) |
Number of Coats | 2 |
Maximum Dry Film Build | 3-4 mils (full system 6 mils) |
Coating Temperature at Application | 18°C (65°F) or higher |
PHYSICAL PROPERTIES:
Specific Gravity: 1.03 ± 2%
Viscosity: 3500-4000 cps @22C
Solids Content: 22% by wt.
Flash Point: >75°C
VOC’s (g/l): <5 g/l
VOC’s (Less Exempt): 9 g/l
DRYING TIMES:
Air dry:
(20°C/68°F)
Dry to Touch: 10-15 Minutes
Dry to Sand: 1 Hour
Dry to Recoat: 1-2 Hours
Dry to Stack: 2-4 Hours
Conventional Oven:
(40-45°C/104-113°F)
Dry to Touch: 5-10 Minutes
Dry to Sand: 30 Minutes
Dry to Recoat: 30-60 Minutes
Dry to Stack: 1-2 Hours
Sun-Spot IR Cure:
Flash off: Not Required
Direct Cure: 4-5 minutes @60-70°C/140-160°F
Rack Cure: 10-15 minutes @10%+ power
Cool: 15 minutes
Product is dry to sand (or stack) after cooling
TYPICAL SYSTEMS:
Natural Look on White Oak & Various Woods (no wood wetting)
Sand 180
ELNYC900 00 Envirothane 900 Raw Clear Natural Effect +2% CAT150
Sand using 320 grit sandpaper
ELNYC900 00 Envirothane 900 Raw Clear Natural Effect +2% CAT150
Super Matt Clear over Stains on Various Woods (wood wetting & more clarity)
Sand 180
ELNYC900 00 Envirothane 900 Raw Clear Natural Effect +10% CAT100LV
Sand using 320 grit sandpaper
ELNYC900 00 Envirothane 900 Raw Clear Natural Effect +10% CAT100LV
Super Matt Solid Dark Colours on various woods (0.5-2 sheen)
Sand 180
ELNYC900 00 Envirothane 900 Raw Clear Natural Effect +2% CAT150 or 10%
CAT100LV + 5% 896-9901 black tinter or tints of choice
Sand using 320 grit sandpaper
ELNYC900 00 Envirothane 900 Raw Clear Natural Effect +2% CAT150 or 10%
CAT100LV + 5% 896-9901 black tinter or tints of choice
GENERAL INFORMATION:
Use stainless steel equipment for all water based products. When switching between solvent and water based products in the same spray equipment we suggest the following:
- From Solvent to Water: Wash with acetone, then wash with water.
- From Water to Solvent: Wash with water, then wash with acetone.
Keep containers closed when not in use and keep from freezing.
These products are designed for industrial use only. Please refer to the Safety Data Sheet prior to use.
SHELF LIFE:
12 months in unopened containers
STORAGE
Disclaimer: Every reasonable precaution is taken in the manufacture of our products to ensure that they comply with our standards. The information given herein is correct to the best of our knowledge. Any suggestions made by us covering the use of our products are based on experience and/or tests believed to be reliable. However, because the use of any product of our manufacture is completely beyond our control, including for example, the method and conditions of application, no guarantee or warranty, expressed or implied, is made. Manufacturer’s maximum liability shall be to replace such quantity of product determined by our laboratory to be defective. User shall determine the suitability of the product for his intended use and assumes all risk and liability in connection therewith.